Aruba 2930F 48G PoE+ 4SFP Switch (JL262A, JL262ACM) 1

I/O ports and slots

48 RJ-45 autosensing 10/100/1000 PoE+ ports (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type 1000BASE-T, IEEE 802.3at PoE+); Duplex: 10BASE-T/100BASE-TX: half or full; 1000BASE-T: full only

4 SFP

Additional ports and slots

1 dual-personality (RJ-45 or USB micro-B) serial console port

Physical characteristics

Dimensions

17.42(w) x 11.98(d) x 1.73(h) in (44.25 x 30.42 x 4.39 cm) (1U height)

Weight

9.83 lb (4.46 kg)

Memory and processor

Dual Core ARM Cortex @ 1016 MHz, 1 GB DDR3 SDRAM; Packet buffer size: 12.38 MB 4.5MB Ingress/7.875MB Egress, 4 GB eMMC

Performance

1000 Mb Latency

< 3.8 µs (64-byte packets)

Throughput

up to 77.4 Mpps

Switching capacity

104 Gbps

Routing table size

2,000 IPv4, 1,000 IPv6 in hardware, 200 OSPF, 256 Static, 10,000 RIP

MAC address table size

32768 entries

Environment

Operating temperature

32°F to 113°F (0°C to 45°C); up to 5000 Feet, - 0C to 40C (32F to 104F) up to 10000 Feet

Operating relative humidity

15% to 95% @ 104°F (40°C), noncondensing

Non-operating/Storage temperature

-40°F to 158°F (-40°C to 70°C); up to 15000 Feet

Non-operating/Storage temperature

15% to 95% @ 149°F (65°C)

Acoustic

Power: 55.7 dB, Pressure: 41.7 dB

Airflow direction

Side-to-side

Electrical characteristics

Power efficiency certifications

80plus.org certification: Silver

Maximum heat dissipation

293.0 BTU/hr (309.1 kJ/hr)

Voltage

100 - 127 / 200 - 240 VAC, rated

Current

5.1/2.5 A

Maximum power rating

459 W

Idle power

48.6 W

PoE power

370 W PoE+

Frequency

50/60 Hz

Notes:

­ Idle power is the actual power consumption of the device with no ports connected.

­ Maximum power rating and maximum heat dissipation are the worst-case theoretical maximum numbers provided for planning the infrastructure with fully loaded PoE (if equipped), 100% traffic, all ports plugged in, and all modules populated.

Safety

UL 60950-1, 2nd Edition; UL 62368-1: 2nd Edition; EN 60950-1:2006 +A11:2009 +A1:2010 +A12:2011+A2:2013; IEC 60950-1:2005 +A1:2009 +A2:2013; EN 62368-1: 2nd Edition; CSA 22.2 No. 60950-1-07 2nd; IEC-62368-1: 2nd Edition; EN 60825-1:2014 / IEC 60825-1:2014 Class 1

Emissions

EN 55032:2012/CISPR 32 Class A; FCC CFR 47 Part 15 Class A; VCCI Class A; ICES-003 Class A; CNS 13438

Immunity

Generic

EN 55024:2010/CISPR 24

ESD

IEC 61000-4-2

Radiated

IEC 61000-4-3

EFT/Burst

IEC 61000-4-4

Surge

IEC 61000-4-5

Conducted

IEC 61000-4-6

Power frequency magnetic field

IEC 61000-4-8

Immunity

Voltage dips and interruptions

IEC 61000-4-11

Harmonics

IEC/EN 61000-3-2

Flicker

IEC/EN 61000-3-3

Management

Aruba Central; Aruba AirWave Network Management; IMC - Intelligent Management Center; Command-line interface; Web browser; Configuration menu; SNMP manager; Telnet; RMON1; FTP

Services

Refer to the Hewlett Packard Enterprise website at http://www.hpe.com/networking/services for details on the service-level descriptions and product numbers. For details about services and response times in your area, please contact your local Hewlett Packard Enterprise sales office.

Enhanced Capabilities

Unified Wired and Wireless Support

Aruba ClearPass Policy Manager

automatically configures switch for different settings such as VLAN, CoS, PoE max power, and PoE priority when an Aruba access point is detected.

defines a set of switch-based policies in areas such as security, authentication, and QoS. A user role can be assigned to a group of users or devices, using switch-based local user role or download from ClearPass

automatically enforces user, device and application-aware policies on Aruba wired and wireless networks. Automated device profiling, role-based access control, and Layer 7 firewall features deliver enhanced visibility and performance for a better overall experience for both IT and end users alike.

provides a secured tunnel to transport network traffic on a per-port or per-user-role basis to an Aruba Controller. In per-user-role Tunneled Node, users are authenticated with ClearPass Policy Manager which can direct the traffic to be tunneled to Aruba controller or switch locally

allows ClearPass to do accounting for clients with static IP address

Software-defined networks

Supports multiple programmatic interfaces, including REST APIs and Openflow 1.0 and 1.3, to enable automation of network operations, monitoring, and troubleshooting.

Quality of Service (QoS)

for classification into eight priority levels mapped to eight queues

based on TCP/UDP port numbers

sets the IEEE 802.1p priority tag based on IP address, IP Type of Service (ToS), Layer 3 protocol, TCP/UDP port number, source port, and DiffServ

sets per-port ingress enforced maximums and per-port, per-queue minimums

provide graceful congestion management

throttles unicast packets with unknown destination addresses and limits flooding on the VLAN

Connectivity

available on select models

provides automatic adjustments for straight-through or crossover cables on all 10/100 and 10/100/1000 ports

12x 1Gbps Ethernet PoE+ ports and four built-in uplinks (2x SFP+ and 2x 1GBASE-T). Built-in power supply.

provides up to 30 W per port that allows support of the latest PoE+-capable devices such as IP phones, wireless access points, and security cameras, as well as any IEEE 802.3af-compliant end device; eliminates the cost of additional electrical cabling and circuits that would otherwise be necessary in IP phone and WLAN deployments

IPv6

Performance and efficiency

- 80 PLUS Silver Certified power supply

increases power efficiency and savings

- Energy-efficient Ethernet (EEE) support

reduces power consumption in accordance with IEEE 802.3az

providing very low latency, increased packet buffering, and adaptive power consumption

allows for increased performance by selecting the number of queues and associated memory buffering that best meet the requirements of the network applications

- Virtual Switching Framework (VSF) front plane stacking creates one virtual resilient switch from up to eight switches.

Notes: Requires ArubaOS-Switch 16.06 software.

- Ring topology supports up to an 8-member stack

- Virtualized switching provides simplified management as the switches act as a single chassis when stacked

Convergence

automatically prevent flooding of IP multicast traffic

defines a standard extension of LLDP that stores values for parameters such as QoS and VLAN to configure automatically network devices such as IP phones

facilitates easy mapping using network management applications with LLDP automated device discovery protocol

support multiple methods (automatic, IEEE 802.3at dynamic, LLDP-MED fine grain, IEEE 802.3af device class, or user-specified) to allocate and manage PoE/PoE+ power for more efficient energy savings

assigns attributes such as VLAN and QoS using a locally configured profile that can be a list of MAC prefixes

includes PIM Sparse and Dense modes to route IP multicast traffic (limited to 16 interfaces)

supports one-to-many and many-to-many media casting use cases such as IPTV over IPv6 networks

Monitor and diagnostics

allows detailed monitoring of the transceiver settings and parameters

Resiliency and high availability

provides high link availability by allowing multiple spanning trees; provides legacy support for IEEE 802.1d and IEEE 802.1w

allows groups of two routers to dynamically back each other up to create highly available routed environments for IPv4 and IPv6 networks (limited to 128 VRs)

support up to 60 static or dynamic trunks with each trunk having up to eight links (ports) per static trunk

provides easy-to-configure link redundancy of active and standby links

provide complete support of SNMP; provide full support of industry-standard Management Information Base (MIB) plus private extensions; SNMPv3 supports increased security using encryption

Simplified configuration and management

cloud based management platform offers simple, secure, and cost effective way to manage switches

simplifies installation of the switch infrastructure using Aruba Activate or a DHCP-based process with AirWave and Central Network Management

provides configuration automation for campus networks

supports both cloud-based Central and on-premises AirWave with the same hardware, ensuring management platform changes without ripping and replacing switching infrastructure

Manageability

provides independent primary and secondary operating system files for backup while upgrading

allow assignment of descriptive names to ports

finds and fixes common network problems automatically, then informs administrator

stored to a flash image

provide advanced monitoring and reporting capabilities for statistics, history, alarms, and events

ingress and egress port monitoring enable more efficient network problem solving

monitors the link between two switches and blocks the ports on both ends of the link if the link goes down at any point between the two devices

monitor quality of voice traffic using the UDP jitter and UDP jitter for VoIP tests

Software releases

Layer 3 services

centralizes and reduces the cost of IPv4 address management

Layer 2 switching

increases the scalability of an Ethernet network by providing a hierarchical structure; connects multiple LANs on a high-speed campus or metro network

supports IEEE 802.1Q (4094 VLAN IDs) and 2K VLANs simultaneously

improves the performance of large data transfers; supports frame size of up to 9220 bytes

isolate select non-IPv4 protocols automatically into their own VLANs

allows each VLAN to build a separate spanning tree to improve link bandwidth usage; is compatible with PVST+

allows automatic learning and dynamic assignment of VLANs

encapsulation (tunneling) protocol for overlay network that enables a more scalable virtual network deployment

Layer 3 routing

provides manually configured routing; includes ECMP capability

facilitate segregation of user data, without adding external hardware

provides RIPv1, RIPv2, and RIPng routing

provides OSPFv2 and OSPFv3 protocols for routing between access and the next layer on the LAN. Only one OSPF area and up to 8 interfaces are supported

uses a classifier to select traffic that can be forwarded based on policy set by the network administrator (limited to 16 next-hop routes)

Customer first, customer last support

When your network is important to your business, then your business needs the backing of Aruba Support Services. Partner with Aruba product experts to increase your team productivity, keep pace with technology advances, software releases, and obtain break-fix support.

For complete details on Foundation Care and Aruba Pro Care, please visit: https://www.arubanetworks.com/supportservices/

Warranty and support

see http://www.hpe.com/networking/warrantysummary for warranty and support information included with your product purchase.

Security

- uses an IEEE 802.1X supplicant on the client in conjunction with a RADIUS server to authenticate in accordance with industry standards

- supports Web-based authentication

- supports MAC-based authentication

- Multiple IEEE 802.1X users per port

provides authentication of multiple devices on a single port; prevents a user from "piggybacking" on another user's IEEE 802.1X authentication

- Concurrent IEEE 802.1X, Web, and MAC authentication schemes per port

switch port will accept up to 32 sessions of IEEE 802.1X, Web, and MAC authentications

includes a Trusted Platform Module (TPM) for secure hardware-based generation and storage of cryptographic keys that can be used for a variety of authentication purposes

provide IP Layer 3 filtering based on source/destination IP address/subnet and source/destination TCP/UDP port number

allows only specified ports to communicate with each other

eases switch management security administration by using a password authentication server

encrypts all transmitted data for secure remote CLI access over IP networks

encrypts all HTTP traffic, allowing secure access to the browser-based management GUI in the switch

allows access only to specified MAC addresses, which can be learned or specified by the administrator

allows users to use a more secure and reliable mode of communications between switch and radius servers over unsecure networks

prevents particular configured MAC addresses from connecting to the network

allows secure file transfer to and from the switch; protects against unwanted file downloads or unauthorized copying of a switch configuration file

helps secure switch CLI logon by optionally requiring either RADIUS or TACACS+ authentication

displays security policy when users log in to the switch

blocks Bridge Protocol Data Units (BPDUs) on ports that do not require BPDUs, preventing forged BPDU attacks

blocks DHCP packets from unauthorized DHCP servers, preventing denial-of-service attacks

blocks ARP broadcasts from unauthorized hosts, preventing eavesdropping or theft of network data

protects the root bridge from malicious attacks or configuration mistakes

enables implementation of a highly granular and flexible access security policy and VLAN assignment specific to each authenticated network user

Configures broadcast control selectively on heavy traffic port uplinks

provides network security by restricting peer-to-peer communication to prevent a variety of malicious attacks; typically a switch port can only communicate with other ports in the same community and/or an uplink port, regardless of VLAN ID or destination MAC address

simplifies first-time deployment of AAA in brownfield deployments by allowing full network access for failed clients and provides instant connectivity as soon as a client is plugged-in

ensures that important infrastructure devices such as IP phones are allowed network access even in the absence of a RADIUS server

allows non-chatty legacy devices to stay authenticated by pinning client MAC addresses to the port until the clients logoff or get disconnected

enhances the switch PKI infrastructure with a simpler, scalable and more secure method of certificate provisioning, re-enrollment and renewal